How do you make Rick Simpson Oil (RSO)?

Top Answer

Medical Jane

Last updated: May 31st, 2016

IMPORTANT: These instructions are directly summarized from Rick Simpson’s official website. Cannabis extractions should always be performed by a licensed professional. If you are venturing to try this extraction process yourself, you will need to be extremely careful when boiling solvents off as the entire process is extremely flammable. AVOID smoking, sparks, stove-tops, heat guns, and red hot heating elements. Set up a fan to blow fumes away from the pot, and set up in a well-ventilated area for whole process.

To make Rick Simpson Oil (RSO), start with one ounce of dried herb. One ounce will typically produce 3-4 grams of oil, although the amount of oil produced per ounce will vary strain to strain. A pound of dried material will yield about two ounces of high quality oil.

  1. Place the completely dry material in a plastic bucket.
  2. Dampen the material with the solvent you are using. Many solvents can be used. You can use pure naphtha, ether, butane, 99% isopropyl alcohol, or even water. Two gallons of solvent is required to extract the THC from one pound, and 500 ml is enough for an ounce.
  3. Crush the plant material using a stick of clean, untreated wood or any other similar device. Although the material will be damp, it will still be relatively easy to crush up because it is so dry.
  4. Continue to crush the material with the stick, while adding solvent until the plant material is completely covered and soaked. Remain stirring the mixture for about three minutes. As you do this, the THC is dissolved off the material into the solvent.
  5. Pour the solvent oil mixture off the plant material into another bucket. At this point you have stripped the material of about 80% of its THC.
  6. Second wash: again add solvent to the mixture and work for another three minutes to extract the remaining THC.
  7. Pour this solvent oil mix into the bucket containing the first mix that was previously poured out.
  8. Discard the twice washed plant material.
  9. Pour the solvent oil mixture through a coffee filter into a clean container.
  10. Boil the solvent off: a rice cooker will boil the solvent off nicely, and will hold over a half gallon of solvent mixture. CAUTION: avoid stove-tops, red hot elements, sparks, cigarettes, and open flames as the fumes are extremely flammable.
  11. Add solvent to rice cooker until it is about ¾ full and turn on HIGH heat. Make sure you are in a well-ventilated area and set up a fan to carry the solvent fumes away. Continue to add mixture to cooker as solvent evaporates until you have added it all to the cooker.
  12. As the level in the rice cooker decreases for the last time, add a few drops of water (about 10 drops of water for a pound of dry material). This will help to release the solvent residue, and protect the oil from too much heat.
  13. When there is about one inch of solvent-water mixture in the rice cooker, put on your oven mitts and pick the unit up and swirl the contents until the solvent has finished boiling off.
  14. When the solvent has been boiled off, turn the cooker to LOW heat. At no point should the oil ever reach over 290˚ F or 140˚ C.
  15. Keep your oven mitts on and remove the pot containing the oil from the rice cooker. Gently pour the oil into a stainless steel container
  16. Place the stainless steel container in a dehydrator, or put it on a gentle heating device such as a coffee warmer. It may take a few hours but the water and volatile terpenes will be evaporated from the oil. When there is no longer any surface activity on the oil, it is ready for use.
  17. Suck the oil up in a plastic syringe, or in any other container you see fit. A syringe will make the oil easy to dispense. When the oil cools completely it will have the consistency of thick grease.

Click here to learn more about Rick Simpson Oil (RSO).

Related Questions

Ask Jane a New Question

Have a question about the cannabis plant or its potential medical applications? Ask Jane by first searching Medical Jane’s database of frequently asked questions and answers. Chances are, someone has already asked and answered your question, so be sure to search Medical Jane before asking the Medical Jane community to answer your question.

Ask a new question


Thank you for subscribing!
There was a problem subscribing, please try again later.

Sign-up to receive the latest medical cannabis research, news, and special offers straight to your inbox.

By subscribing I agree to the Privacy Policy